Skip to content
Arbee Craft

How to Preserve Flowers in Resin: The Honest Guide

A resin coaster with a rose from your wedding bouquet. A pendant holding a bloom from the day your daughter was born. A wall panel with the entire arrangement from a special birthday. The idea is beautiful. The execution is where most people come unstuck — the flower goes into the resin looking perfect, and a month later it's brown, mouldy, or faded to a memory of what it was. This guide covers how to preserve flowers in resin the way it actually works: dry the flower first, choose the right resin, and know when to give up on fresh blooms and use faux instead.

Why Fresh Flowers Rot in Resin

Fresh flowers hold moisture. Rose petals are around 85% water. Even a dry-looking daisy still holds enough water inside its cellular structure to cause problems.

When resin cures, it doesn't dehydrate the flower. It seals the moisture in. The water sits inside the petals, bacteria and mould feed on the organic material, and the flower browns from the inside out — usually starting within a week or two, always finished within a couple of months. The resin block still looks glossy on the outside. The flower inside is done.

The only way to preserve real flowers in resin is to remove the moisture first. That's what this guide is about.

Method 1: Silica Gel Drying (Best Results)

Silica gel is the professional preservation method. It draws moisture out of the flower quickly enough that the shape and colour are largely retained. Fine-grain craft silica is available at most craft, hobby and homewares shops in Australia.

You'll need — an airtight container, enough silica gel to cover your flowers completely, tweezers, and your fresh flowers (trimmed to fit).

  • Fill the container about halfway with silica gel.
  • Place the flowers gently on top, face-up, without overlapping.
  • Slowly pour more silica gel over the flowers until they're completely buried. Tap the container gently to let the gel settle between petals.
  • Seal the container and leave for 5–7 days somewhere warm and dry.
  • Uncover carefully — the flowers will be brittle. Lift them out with tweezers, brush off any clinging silica with a soft paintbrush.

Result: flowers keep their three-dimensional shape and about 80% of their original colour. Ideal for jewellery pendants, small paperweights, and any piece where you want the flower to look like a flower — not pressed flat.

Method 2: Traditional Pressing (Flat Results, Free)

Pressing has been around for centuries because it works. The trade-off is that pressed flowers are flat, not three-dimensional — best for coasters, wall art, and bookmarks rather than pendants or paperweights.

You'll need — heavy books, printer paper, and patience.

  • Place the flower between two sheets of printer paper.
  • Lay the paper inside a heavy book.
  • Stack more heavy books on top for even pressure.
  • Wait 2–3 weeks. Check after week one — if the paper feels damp, replace it with fresh sheets.
  • Once the flowers are fully dry and paper-flat, they're ready to set in resin.

Pressed flowers keep their shape well but lose some vibrancy. Colours often shift toward earthy tones — reds go rust, purples go dusty.

Method 3: Microwave Drying (Fast but Risky)

Microwave drying combines silica gel with heat to speed the process up. Done well, it produces silica-gel-quality results in a fraction of the time. Done badly, it scorches the flowers or leaches all the colour out.

Place flowers in silica gel inside a microwave-safe container. Microwave in 30-second bursts, checking between each burst. Most small flowers dry in 2–4 bursts. Larger blooms may need 5–6.

This method rewards experimentation. Try it on flowers you're not emotionally attached to before you commit a wedding-bouquet rose to the microwave.

Choosing the Right Resin for Preserved Flowers

Two-part epoxy resin is the standard for flower preservation. The long cure time (around 24 hours) gives you room to position the flower, add layers, and troubleshoot bubbles. Its clarity is excellent, which matters when the flower is the star.

UV resin also works for small pieces — cabochons, small pendants, ring inserts — provided you can cure it in thin layers. UV resin can't cure through thick pours (a UV lamp can't reach the bottom of a deep pour), so layer it in stages.

Whichever resin you choose, look for a UV-inhibitor version if the finished piece will be near a window or worn outdoors. UV degradation yellows resin over time — an inhibitor slows this dramatically.

Step-by-Step: Setting Preserved Flowers in Resin

Once your flower is fully dried, here's how to set it.

  • Layer 1 — pour a thin base of resin into your mould. Let it cure fully.
  • Position the dried flower on top of the cured base, face-up if you want the flower visible from the top of the piece.
  • Layer 2 — pour resin slowly over the flower to encapsulate it completely. Pour close to the surface and let the resin flow around the petals rather than dumping it on top.
  • Use a toothpick to gently push air bubbles out from between petals.
  • Let cure fully (24 hours for standard epoxy, per manufacturer's instructions).
  • Optional Layer 3 — a thin top coat for extra clarity and gloss.

Common Mistakes and How to Fix Them

  • Flower turned brown after a few weeks — moisture wasn't fully removed before setting. Dry the flower for longer next time.
  • Air bubbles trapped near the petals — pour too fast, or didn't use a toothpick to work bubbles out. Pour slowly, close to the surface.
  • Flower shifted during cure — didn't wait for the base layer to fully cure before adding the flower.
  • Resin yellowed after months on display — used a resin without UV inhibitor. Switch to a UV-resistant resin for pieces on show.

When to Reach for Faux Flowers Instead

Here's the honest bit. Real flowers in resin are beautiful, sentimental, and — even with the best preservation method — occasionally still go wrong.

If you're selling resin pieces at markets and need a consistent finish, if you're making a keepsake for a friend and want to know it'll still look perfect in ten years, or if you just want to focus on the design rather than the chemistry of dehydrating petals, silk and faux flowers are a genuinely good alternative. Modern silk and paper flowers are cast from real blooms, come in every colour and variety imaginable, and don't rot in resin because there's no moisture to trap in the first place.

The faux flower range at Arbee Craft covers everything from single blossoms and stems through to bulk artificial florals for large resin art pieces. Worth a look before you commit a wedding bouquet to the silica gel jar.

Preserving a Wedding Bouquet — What Actually Works

Wedding bouquets are the highest-emotional-stakes preservation project, so it's worth being clear about what actually delivers a lasting result.

Option 1 — silica-gel dry a few of the most meaningful blooms (a single rose, a sprig of baby's breath, one distinctive filler flower) and set each in a small individual resin pendant or block. Individual small pieces are far more forgiving than trying to preserve the whole bouquet in one large pour.

Option 2 — press key flowers flat and mount them in a framed shadowbox alongside the invitation, ribbon and other bouquet elements. No resin needed, and the result reads as a curated memento rather than a preservation experiment.

Option 3 — use faux versions of the same flower types for a resin keepsake that lasts decades. Match the bouquet's palette and variety and the finished piece captures the look without the risk.

Related Guides

Frequently Asked Questions

Can you preserve fresh flowers in resin?

Not without drying them first. Fresh flowers retain moisture inside the petals; resin seals that moisture in and the flower rots from the inside out. Always dry the flower before setting it.

How long do dried flowers last in resin?

Properly dried flowers in cured resin can last decades. Colour may fade slowly with UV exposure — use a UV-inhibitor resin for pieces on display.

Do you need silica gel to dry flowers for resin?

Silica gel delivers the best three-dimensional results, but pressing (using books) also works if you're happy with a flat finished piece.

Why do flowers go brown in resin?

Trapped moisture. If any moisture remains in the flower when it's sealed in resin, bacteria and mould feed on the organic material and turn the petals brown from the inside.

What's the best resin for preserving flowers?

Two-part epoxy resin with a UV inhibitor is the standard for flower preservation. Long cure time, excellent clarity, and doesn't yellow over time when made with a UV-resistant formulation.